Quality double planer machine wholesale supplier: The most common application involves gluing a coating (veneer, laminate, composite, PVC etc) onto a substratum (MDF, hardboard, plywood, hollow panels, blockwood etc). The basic configuration of the pressing line is comprised of a feed belt, an automatic press and a discharge deck. This configuration can be completed with numerous options, such as glue spreaders, polishers, automatic feeders, disk, roller or belt conveyors, automatic assembling stations, panel turners and stackers. Lines with various degrees of automation can be supplied right up to fully automatic lines that do not require direct intervention by the operator. Read more information at https://www.v-holdmachinery.com/double-side-planner.

The radial arm saw is pretty much a portable circular saw that glides on an adjustable arm suspended over a fixed cutting surface. The blade and motor are connected to the arm by a yoke, which is adjustable along both horizontal and vertical planes, enabling the saw to be swung in a variety of directions. For cross-cut work, position the board flush with the fence at the rear of the saw and draw the blade across the wood. The bevel lock allows the saw to be tilted for cutting angles. You can set it to the desired angle using the protractor on the saw housing. The saw can be swivelled right or left for mitring, or turned a full 90 degrees for ripping. The blade can also be raised or lowered using a crank. The size of the saw is determined by the dimension of the blade the saw can accommodate. As an example a model using a 10 inch blade would be able to cut work-pieces up to 3 inches thick.

Up-acting machines typically apply hydraulic pressure from the centre of the lower beam which pushes the lower beam upwards into a fixed upper beam. Tonnage is applied to the centre of the lower beam in an upward fashion. The flex in the bend tends to be even from left to right. Hydraulics are used to push the lower beam up and gravity is used to return the lower beam down. A loss in power will result in the brake being in the open position. Since the lower beam does move during operation, feedback to the operator is given. Knowing the lower beam is moving can be a safety feature. Down-acting machines are preferred if staged bending is important. Staged bending is a valuable option that can significantly improve productivity while minimising setup time.

The chain mortiser is primarily used for making mortises in doors and windows. It carries an endless chain which has saw type teeth on its outer surface. The chain revolves around a guide bar and cuts the stock. The mortise of the desired length is produced with round bottom corresponding to the profile of the revolving chain. The oscillating bit mortiser carries a oscillating router bit and produces comparatively small mortises suitable for small cabinet and chair work.

Probably the second most important of single woodworking machines in a carpentry shop is the circular saw. It can be used for ripping, cross cutting, mitering, beveling, rabbeting, and grooving. Although there are many types of circular saws such as universal saw, variety saw, bench saw, the basic working parts are common to all. Each has a flat surface or table upon which the work rests while being cut, a circular cutting blade, cut-off guide, and a ripping fence that acts as a guide while sawing along the grains of the wood. The circular saw usually has provisions for tilting the table upto an angle of 45° to enable the machine to cut at different angles required during mitering, levelling, etc. The size of a circular saw is determined by the diameter of the saw blade.

Modern machinery often requires pneumatic pressure, be it for saws, sanders, impact wrenches, grinders, spray guns, washers, stapling, nailing or pneumatic tooling, the compressor has become a necessity. The compressor consists of: motorised pump; tank for storing the compressed air; on/off control; regulator. There’s also a metal frame on which all the parts are mounted, usually with a carrying handle and occasionally wheels. A drill press can be used to drill round holes, sanding, grooving and mortising with the addition of specialised attachments. Find additional info on https://www.v-holdmachinery.com/.

Situated in Lunjiao town, Shunde district of Foshan city, the biggest woodworking machinery production base as well as “the Chinese leading woodworking machinery town”, V-HOLD woodworking machinery manufacture Co.,Ltd is a large well-known company integrated woodworking machinery research, processing, marketing as well as application service. We have one year warranty lifetime maintenance service. 2. For any technical problems you can contact us immediately. We have overseas repair and On-going Technical Support.