Welding masks online store IE today? Whether you’re a professional contractor or a DIY enthusiast and looking for a metal-cutting tool, this disc is a must-have. The cutting wheel is a great way to quickly cut through metal. With 52 wheels, you’ll always have one on hand. It is compatible with all 4-1/2 inch (115mm) angle grinders with 7/8 inch (22.2mm) arbor. The thickness of the wheel is 0.045 inch (1.2mm). You can operate this up to 13,300 RPM When it comes to precision and burr-free cutting, the Truswe Metal and Stainless Steel Cutting Wheel for Angle Grinder is tough to beat. This ultra-thin design delivers fast and accurate performance, with minimal material loss. The Metal Cutting Discs are made of aluminum oxide grains which are more safe than other wheel types. These discs should only be used when wearing all applicable safety gear because they can fly off the wheel and injure you if not careful. You should read the instructions before using this power tool. It is a heavy duty cutting disc that is fitted to any angle or side grinder. It will cut with ease through sheet metal, plastics, fiberglass, Plexiglas, ceramic tiles and even rubber. Read extra details on welding curtains online store Ireland.

One of the “cardinal sins” that almost every shop commits is over-welding. This means that if the drawing calls for a 1/4″ fillet weld, most shops will put down a 5/16″ weld. The reasons? Either they don’t have a fillet gauge and are not exactly sure of the size of the weld they are producing or they put in some extra to “cover” themselves and make sure there is enough weld metal in place. But, over-welding leads to tremendous consumable waste. Let’s look again at our example. For a 1/4″ fillet weld, the typical operator will use .129 lbs. per foot of weld metal. The 5/16″ weld requires .201 lbs. per foot of weld metal – a 56 percent increase in weld volume compared to what is really needed. Plus, you must take into account the additional labor necessary to put down a larger weld. Not only is the company paying for extra, wasted consumable material, a weld with more weld metal is more likely to have warpage and distortion because of the added heat input. It is recommended that every operator be given a fillet gauge to accurately produce the weld specified – and nothing more. In addition, changes in wire diameter may be used to eliminate over-welding.

How to pick a welder tips: Duty cycle: The advertised amperage of the machine offers a headline guide, but the duty cycle of the machine gives up the truth. Light industrial machine duty cycles can be as low as 20%, but more heavy duty MIG’s should range between 40-60%. If a 300amp MIG has 30% duty cycle for instance, it’s on the edge of acceptability. Duty cycle is determined by how many minutes out of 10, it can weld at 100%. Duty cycle testing: MIGS tested at 20 Degrees & 40 Degrees we consider good. (Beware any manufacturer who doesn’t quote an ambient temperature for testing) Manufacturer’s warranty: Always a great guide to quality. A three year warranty is good. Weld characteristics: Make sure the arc is smooth & suits your application. (Some machines are better suited at the low range and others at higher amperage range).

The Hobart Ironman 240 is the updated version to the Ironman 230 that recently has been discontinued. The 240 is a well-reviewed welder that delivers a wide range of power from 30 to 280 amps in a heavy-duty American-made chassis. Hobart equips the Ironman series with its “soft arc” technology for an easier striking, more spatter-free arc. If you are looking to weld aluminum, then like most of their MIG welders, they offer the package with a SpoolRunner 200 spool gun found here, for a few hundred extra bucks. This is a full-sized platform, offering a 15-foot gun connection and able to load a 44-pound spool of wire. Hobart backs the Ironman 240 with a strong five-year limited warranty. The power regulator has 12 notch settings for easy feel when setting the power level with gloves. This power regulator knob seems to be a problem for some users who have reported issues with the knob rotating freely and not changing the power setting. The only downside to this model is that it is unable to run directly off of a generator as it causes problems with the SCR firing timing of the welder. This makes it a bit less portable than some other welders, but nothing you can’t work around. Overall, this is a quality industrial-grade welder which is ideal for farm work which has been compared to Miller 252 – just without the digital screens and a few other features that most people wouldn’t need, but costs a lot less making it excellent value for the money.

Several tips on welding equipment, MIG and TIG welders, plasma cutters. When appearance counts, TIG welding creates a high quality, clean weld that is far less likely to distort the metal by using a nonconsumable tungsten electrode. There is no need to worry about splatter because it only uses the necessary amount of filler metal needed in the welding puddle, making for the highest quality weld in every respect. However, TIG is fairly specialized and requires a good deal of training in order to master it—so make sure any TIG welder purchase is paired with a plan to take welding classes. Instead of the point and shoot simplicity of MIG welding, TIG requires the use of a foot pedal to regulate the welding process. A filler rod that is separate from the torch that must be fed in gradually. Many professional welders prefer TIG because it can weld a wide variety of metals and because of the versatility of argon gas used during TIG welding. There is no slag to block the view of the weld puddle. Argon gas can weld any metal at any thickness with TIG welding, and therefore there is no need to change the gas depending on the project.

Finally, if you’re looking for a home welder, then you don’t necessarily need the most powerful machine on the market. Some people invest in MIG welders specifically to support their home-based projects, when they’re creating something new in the garage, or working on adaptions to pieces of machinery and furniture. The Clarke MIG151EN is designed for the DIYers who can’t afford to compromise on quality. Complete with professional specifications like a non-live torch and an extra-tough protective coating on the front and rear, the Clarke turbo MIG welding machine comes with everything you need to start welding at home. There’s a thermal overload protection system to give you complete peace of mind, as well as a very powerful wire drive motor included. Additionally, you’ll be pleased to know that all Clarke products comply with the highest quality of European and safety standards. As a winner of multiple third-party awards, Clarke offers a high-performance option for anyone searching for an arc welder for home use. The rotary power selection system also means that you can choose the level of performance you need with ease. Read more info at https://www.weldingsuppliesdirect.ie/.

US tool brand DeWalt are known for making the best angle grinders, and the DCG405N is a step above the competition. Cutting the cord once and for all, this is a powerful grinder that makes use of DeWalt’s excellent XR battery system. This Dewalt angle grinder is not just a powerful cordless grinder though. The grip shape is supremely comfortable, and the whole unit weighs just 1 kg without the battery installed. You can lock-off the power switch when you need to get the grinder into awkward spots as well. This brushless angle grinder also features a host of clever safety features. I like the no-volt release to prevent accidental start-ups when a new battery is installed. The electronic brake and clutch are essential for safe operation too. The 18V brushless motor is ideal for battery use. It can make 69 cuts in ½” steel rebar when used with a 5.0 Ah battery. It doesn’t come with any batteries or one of DeWalt’s excellent TSTAK cases though, which is the case with bare power tools.

The X-Tractor from Lincoln has a “Mini” in it, which is self-explanatory. The machine isn’t as heavy-duty as most welding fume extractors, but no other device can beat the X-Tractor Mini in terms of portability. The X-Tractor Mini is compact and extremely lightweight. You can just pick it up and set it anywhere you like, from your garage to a store. But, the lighter weight doesn’t compromise efficiency. 2 Different Airflow Settings and 2.4 HP Motor This portable weld fume extractor comes with 2 different settings to choose the preferred airflow. The lower one will generate 95 cubic feet per minute, and the higher one will generate 108 cubic feet of airflow per minute. The amount of airflow seemed a little less to me, but you can’t expect more from a 2.4 HP motor. Besides, the size of the machine speaks for itself that it’s highly portable, which requires a bit of compromising on the power’s end.

Evolution Power tools magnetic drill press is one of the top-rated magnetic drill machines. It is most famous for its lightweight and compactness, excellent and well-constructed magnetic drill machine at a reasonable price. This is ideal for bridges, I-beams, and framework. This can provide 1300 Kgf. Or 2860 lbs f magnetic adhesion. Its maximum core diameter is about 28 mm or 1-1/8 inch. It can give a depth cut maximum of 50 mm or 2 inches. Evolution Power tools magnetic drill press also provide Weldon shank cutter fitting type -19 mm. It also offers a wide variety of tools to be used with Evolution Power tools magnetic drill press. This package includes a wide range of annular cutter, step drills and mini cutters, evolution cutting fluid.

The ESAB group is owned by Colfax Corporation. Over 100 years after the company was founded, ESAB serves a global market for welding and cutting equipment. The group is organized in the regions Europe, North America, South America, Asia/Pacific and India. ESAB is represented in almost every country by subsidiaries or agents. Sales and support is established in 80 countries and there are 26 manufacturing plants across four continents. Visit the web site of your nearest ESAB office to find out more. Customers Talk, We Listen – The voice of the customer will always drive the development of our strategic plans and actions. Living this value is done by getting Customer Input and Expectations, at every opportunity, and by differentiating ourselves in How We Deliver to our customers. Innovation Defines Our Future – Individual and organizational creativity will drive breakthrough ideas for technology, products, solutions, and processes. We live this value by providing differentiated customer solutions, creating products and services that improve quality of life and environmental stewardship through Creative Thinking, and by understanding What Innovation Brings.

Welding Supplies Direct are the UK distributor for GPPH welding tables, manufactured to the highest standards in Europe. GPPH’s range of welding benches and tables are laser cut for precision and are used in every branch of industry. These welding tables offer perfect flatness (+/- 0.5MM) & are made from 15MM thick S355J2+N grade steel. Our modular welding benches come equipped with a hole system of all sides (tabletop & all sides); the holes are 28MM in diameter and have a chamfered edge for easy tool assembly. You have the option of standard legs or castors being fitted, too.

If you’re a beginner welder but don’t mind splashing the cash for a top of the range welder, then try the Millermatic 141. Miller have really pushed the boundaries of usability with this welder and it features an auto-set feature for an easy set up, and infinite voltage and wire speed control. All you have to do is select the thickness of the metal you’re welding and you’re ready to start welding straight away. If you open up the machine you can tell that all the parts are great quality and really durable as well. There are more powerful welders on the market for the price, but there’s nothing better for welding up to 3/16 inch steel. See the full review here.

Out of a huge product range of the Dirty Pro Tools, we have found a top-grade MIG welder that turned out to be so good that we have decided to add it to this shortlist. It is the tool for welding metalware of medium thickness with the output range from 50? to 60?, best for sheets up to 2 mm thick. In addition, a pretty powerful converter of this welder allows working for about 6 minutes at 50?. So, you’ll be able to weld thin pieces for a good while, and the fan will provide a decent cooling of the tool. However, when the MIG welder overheats, the red light will flash telling you to stop welding and make a pause. By the way, you can pick either of 4 available amperage settings and adjust the wire feeding speed for reliable and straight welds. We were pleased by the package that includes a face shield, a clipping hammer, a brush and a spool of welding wire, so you can start welding right after unpacking the unit. So, this Dirty Pro Tools welder is one of the most affordable models for people seeking a mid-power machine to weld fine metal sheets.

UK market pick: Through our extended research of these particular welders, we found dozens of videos and articles and reviews to guide the viewer through the process of buying, setting up, and using these machines. We hope this buying guide will help you in choosing the welder that most suits your needs. After further explanations of the welding process and what to look for when buying, there will be a list of ten well-known metal inert gas welders that will each be reviewed briefly.

Never drag, roll, or drop cylinders during the use. Always take care to maintain the valve caps during the transport. Avoid lifting the cylinder using a valve cap. Never store the cylinders for a long time period. Gas cylinders should only be purchased in small quantities. Never store them for long time periods. It is important to follow extreme precautions and safety measures while working with industrial gas cylinders due to several hazards and risks posed by them. Sourcing these cylinders from a reliable manufacturer is the most important safety measure for any facility owner using these cylinders.